Welding 101
What Is Stickout in MIG Welding? Stickout vs CTWD Explained

Correct machine settings are only part of a good weld. In metal inert gas (MIG) welding, gun distance also affects current, penetration, and arc behavior.
Stickout in MIG welding is often confused with Contact Tip to Work Distance (CTWD). These measurements are related, but mixing them up can put the gun in the wrong position.
This article covers the measurements, starting lengths for common setups, and signs of poor stickout. It also shows how to hold a steady distance through the weld.

Proper Stickout for MIG Welding
Source: https://www.youtube.com/watch?v=LKi-BAmNHjQ
What Is Stickout in MIG Welding
In everyday shop use, stickout often refers to electrode extension, the unmelted wire from the contact tip to the melting wire end. This wire carries welding current, so its length can affect current and arc behavior.
The American Welding Society (AWS) defines stickout from the nozzle end. Electrode extension starts at the contact tip.
When checking a diagram or equipment manual, confirm where the measurement starts. All recommended wire lengths below refer to electrode extension.

MIG Welding Stickout Diagram
Source: https://www.pinterest.com/pin/570760952752337341/
Stickout vs. CTWD: What Is the Difference
CTWD includes electrode extension and the arc gap. Electrode extension includes only the unmelted wire. While the arc is established, their relationship can be simplified as:
CTWD ≈ Electrode Extension + Arc Length
| Measurement | Measure From | Measure To |
|---|---|---|
| Stickout, AWS definition | Nozzle end | Melting wire end |
| Electrode extension | Contact tip end | Melting wire end |
| Arc length | Melting wire end | Weld pool |
| CTWD | Contact tip end | Workpiece at the weld |
In short-circuit MIG, the wire repeatedly touches the puddle. Each contact briefly closes the arc gap, even when the gun position stays the same. This is why wire length and gun-to-work distance should not be treated as the same measurement.
How Contact Tip Position Affects Stickout
If the contact tip is recessed inside the nozzle, part of the electrode extension will also be inside the nozzle. For example, a 1/8-inch tip recess plus 3/8 inch of visible wire gives an actual electrode extension of 1/2 inch. Measuring only the visible wire would leave out the hidden section.
When the contact tip is flush with the nozzle, nozzle-based stickout and electrode extension are the same. If the tip extends beyond the nozzle, nozzle-based stickout is longer than electrode extension. The nozzle edge is therefore a reliable reference only when you know the contact tip position.

MIG Contact Tip Position and Wire Stickout
How to Measure Stickout in MIG Welding
Measure stickout with the welder turned off, using the measurement specified for your setup. A ruler gives you a clear starting reference. With practice, you can learn to judge and maintain that distance through your welding helmet.
Before making a test weld, follow these steps:
-
Make the gun safe. Turn off and unplug the welder. Let the nozzle and contact tip cool before handling them.
-
Locate the contact tip. Check where the tip sits relative to the nozzle. If you remove the nozzle, reinstall it correctly before welding.
-
Measure along the wire. Hold the ruler parallel to the wire and measure from the end of the contact tip. Trim the wire to the recommended starting length.
-
Check CTWD if needed. Hold the gun at the intended welding angle. Measure from the contact tip to the point where the arc will start.
Remove the ruler before turning the welder back on. The wire length you set is only a starting reference. During welding, wire feeding and melting determine the actual electrode extension, so use the test weld to confirm your working distance.
What Is the Correct Stickout for MIG Welding
For many carbon steel solid wire in short-circuit MIG, 3/8 to 1/2 inch (10–13 mm) of electrode extension is a common starting range. Follow the wire or machine instructions for your exact setup.

Proper Welding Position for Consistent Stickout
Source: https://www.youtube.com/watch?v=uThaKtlpFBk
Stickout for Different Transfer Modes
Metal transfer mode describes how molten metal moves from the wire into the weld pool. Match the electrode extension to the transfer mode you are using:
-
Short-circuit transfer: The range above suits many steel setups. Small-diameter wire or low-current work may use a shorter extension, so check the machine chart or wire recommendation.
-
Spray transfer: Spray MIG often uses a longer electrode extension than short-circuit transfer. A common range for conventional setups is about 1/2 to 3/4 inch (13–19 mm), depending on the wire, current range, and welding procedure.
-
Pulsed transfer: Use the electrode extension or CTWD listed for the selected pulse program. The correct distance can vary with the welder, wire, and program.
Factors That Affect Recommended Stickout
Several factors can affect the recommended stickout:
-
Wire material and diameter: Electrical resistance and melting behavior vary by wire type and size. A setting for steel may not suit aluminum or another diameter.
-
Operating current: Current and wire feed speed can affect the recommended stickout.
-
Transfer mode: Short-circuit, spray, and pulsed MIG may call for different distances.
-
Joint access: Deep grooves and tight corners may require a different gun setup to maintain proper stickout.
-
Welding procedure: If a procedure specifies a distance range, follow that requirement.
Synergic mode on a welder such as the YESWELDER MIG-205DS PRO can help establish starting voltage and wire feed speed. Keep the gun distance steady while testing these settings so changes in hand position do not affect the results.
Recommended Products
Recommended Products
How Does Stickout Affect Weld Quality?
With conventional constant-voltage (CV) MIG, a longer electrode extension generally lowers amps, while a shorter one raises them. This assumes voltage and wire speed stay unchanged. Longer wire adds resistance and heats up before the arc, but the lower current can reduce heat going into the joint.
Too Much Stickout
An extension beyond the recommended range can cause:
- Poor penetration: Lower current may leave the weld too shallow or poorly fused to the sides of the joint.
- An uneven arc: Metal transfer can become less stable, leading to more spatter and an uneven bead.
- Poor gas coverage: If the nozzle also moves too far away, air can reach the puddle and cause porosity.
Too Little Stickout
Holding the contact tip too close can cause:
- Burn-through: Higher current can melt through thin sheet metal, especially near an edge or gap.
- Tip damage: The contact tip receives more arc heat, while spatter builds up around the gun opening.
- Burnback: The wire can melt into the contact tip, particularly if wire feeding slows or stops.
These signs can also come from poor feeding, dirty metal, or wrong settings. If correcting the distance does not help, inspect the MIG gun parts, gas supply, and joint before changing several controls.

MIG Stickout Length Comparison
Source: https://www.youtube.com/watch?v=Xod-ByrxHg4&t
How to Maintain Consistent Stickout
Support your hands and follow the joint at a steady distance. Your hand needs to rise or fall with the workpiece, especially on curved tubing or uneven repairs.
-
Set up your position. Use both gloved hands when practical. Rest your forearm on a cool, stable support and keep the cable free of snags.
-
Plan the full pass. With the machine off, move the gun along the joint. Make sure you can reach the end without stretching or twisting your wrist.
-
Keep the puddle in view. Move your head for a better view instead of lifting the gun. Keep the gun angle and travel speed steady while you practice.
-
Check the gun. Worn or dirty MIG gun parts can disturb the arc. Clean the nozzle and check the contact tip and liner before blaming your hand control.
Frequently Asked Questions
1. Can I Use the Same Stickout for Gasless Flux-Cored Wire?
Not automatically. Many self-shielded flux-cored wires require a longer electrode extension than solid-wire short-circuit MIG. Follow the wire manufacturer’s recommended range and make sure you are measuring from the correct reference point.
2. Should I Trim the Wire Before Every Restart?
Trim the wire if it is too long, bent, or has a large ball on the end that causes poor arc starts. Switch off the welder before trimming the wire.
3. Can More Shielding Gas Fix a Long Stickout?
No. Increasing shielding gas cannot correct the change in welding current caused by excessive stickout, and too much gas flow can disturb shielding. Restore the recommended gun distance first.
4. Does Pushing or Pulling Change the Recommended Stickout?
Not by itself. Travel direction does not automatically require a different stickout. Use the recommended range for your wire type and transfer mode unless the welding procedure specifies otherwise.
5. Why Does the Wire Burn Back When I Release the Trigger?
Wire burnback can happen when the arc remains active too long after wire feeding stops. Check the burnback setting if your welder has one, and make sure the wire feeds smoothly through the gun.
Final Thoughts
Good stickout in MIG welding starts with knowing which distance your setup requires. Use the contact tip as the reference for electrode extension, account for its position inside the nozzle, and choose a length suited to the wire and transfer mode. Then focus on holding it through the pass.
When a test weld works well, note the wire, settings, and tip and nozzle setup. That makes the result easier to repeat next time. A steady distance, clear view, and comfortable hand position will help more than changing settings after every uneven bead.


